Home > Products > Centrifugal Pump > Cost-Effective Single-Stage Single-Suction Water Pump Comparable to Grundfos
Cost-Effective Single-Stage Single-Suction Water Pump Comparable to Grundfos
Product feature1. The pump has compact structure, small volume and beautiful appearance. Its standThe gravity center of the type structure is lower and coincides with the foot center of the pump, thus enhancing the pump. The stability of the operation and use to raise life.2. Easy installation. T......
Send Inquiry
Product Description
Product feature
1. The pump has compact structure, small volume and beautiful appearance. Its stand
The gravity center of the type structure is lower and coincides with the foot center of the pump, thus enhancing the pump. The stability of the operation and use to raise life.
2. Easy installation. The entrance and exit paths are the same and in the same center. On-line, it can be directly installed on any part of the pipeline like a valve.
Bits. The motor with rain cover can be used outdoors. The pump is equipped with Install the foot so that the pump can be installed stably.
3. Stable operation, low noise and high component concentricity. The machine adopts low-noise bearings and is equipped with a non-stop oiling device. The impeller of the pump has excellent dynamic and static balance, no vibration in operation, and is improved Make good use of the environment.
4. No leakage ~ The shaft seal is mechanically sealed with corrosion-resistant hard alloy.
5. Easy maintenance. There is no need to remove the pipe, just remove the pump. Cover the nut and take out the motor and transmission assembly for maintenance
6. The pump can be vertical or horizontal according to the site use conditions. Type, multi-mode installation, according to the requirements of flow head, using Parallel and series connection method to increase the required flow head.
Working Conditions
1. The high working pressure of the pump system is ≤1.6MPa, i.e. pumping
Inlet pressure+pump lift ≤1.6MPa, please indicate the system when ordering Working pressure. When the inlet pressure is greater than 0.4MPa, or the pump system is lifted. When the working pressure of the system is greater than 1.6MPa, it shall be separately ordered. Out, so that when manufacturing, pump flow and coupling parts cast steel is used.
2. Applicable medium: the medium of clean water pump shall be free of corrosive liquid. The volume of solid insoluble matter shall not exceed the unit volume 0.1%, particle size < 0.2mm, such as medium with fine particles Please explain when ordering.
3. The ambient temperature shall not exceed 40ºC, and the relative humidity shall not exceed over 95%.
1. The pump has compact structure, small volume and beautiful appearance. Its stand
The gravity center of the type structure is lower and coincides with the foot center of the pump, thus enhancing the pump. The stability of the operation and use to raise life.
2. Easy installation. The entrance and exit paths are the same and in the same center. On-line, it can be directly installed on any part of the pipeline like a valve.
Bits. The motor with rain cover can be used outdoors. The pump is equipped with Install the foot so that the pump can be installed stably.
3. Stable operation, low noise and high component concentricity. The machine adopts low-noise bearings and is equipped with a non-stop oiling device. The impeller of the pump has excellent dynamic and static balance, no vibration in operation, and is improved Make good use of the environment.
4. No leakage ~ The shaft seal is mechanically sealed with corrosion-resistant hard alloy.
5. Easy maintenance. There is no need to remove the pipe, just remove the pump. Cover the nut and take out the motor and transmission assembly for maintenance
6. The pump can be vertical or horizontal according to the site use conditions. Type, multi-mode installation, according to the requirements of flow head, using Parallel and series connection method to increase the required flow head.
Working Conditions
1. The high working pressure of the pump system is ≤1.6MPa, i.e. pumping
Inlet pressure+pump lift ≤1.6MPa, please indicate the system when ordering Working pressure. When the inlet pressure is greater than 0.4MPa, or the pump system is lifted. When the working pressure of the system is greater than 1.6MPa, it shall be separately ordered. Out, so that when manufacturing, pump flow and coupling parts cast steel is used.
2. Applicable medium: the medium of clean water pump shall be free of corrosive liquid. The volume of solid insoluble matter shall not exceed the unit volume 0.1%, particle size < 0.2mm, such as medium with fine particles Please explain when ordering.
3. The ambient temperature shall not exceed 40ºC, and the relative humidity shall not exceed over 95%.
| model | flow rate | power |
| LISG50-315(I) | 25m3/h | 30kw |
Related Category
Water Pump
Centrifugal Pump
Plunger Pump
Piston Pump
Diaphragm Pump
Gear Pump
Vacuum Pump
Pump Parts
Screw Pump
Gasoline & Gas Pump
Self-Priming Pump
Vane Pump
Other Pump & Vacuum Equipment
Pressure Pump
Jet Pump
Peristaltic Pump
Send Inquiry
Please Feel free to give your inquiry in the form below. We will reply you in 24 hours.
